Gnypahalan - SuSE 7.2: Difference between revisions
Jump to navigation
Jump to search
(New page: <pre> LINUX INSTALLATION - LOG: (maintained by Nightmare@hell-on-earth.org) ======================== OS: SuSE 7.2 PC: AMD-DURON-1000 384MB (--> will decrease to 128MB) Advansys ...) |
m (moved Configuraton Gnypahalan SuSE 7.2 to Gnypahalan - SuSE 7.2) |
||
| (One intermediate revision by one other user not shown) | |||
Latest revision as of 11:38, 26 April 2013
LINUX INSTALLATION - LOG: (maintained by Nightmare@hell-on-earth.org)
========================
OS: SuSE 7.2
PC: AMD-DURON-1000
384MB (--> will decrease to 128MB)
Advansys SCSI Card,
ATI 64Play,
Net Genius PCI RLT8139B 10/100,
Net Unex PCI RLT8139C 10/100,
IBM HDD 8G4,
??? HDD 2G (disconnected),
PIONEER SCSI CD-ROM 32x Slot-In,
YAMAHA SCSI ReWriter 16x/4x/4x,
Microsoft IntelliMouse 1.2a,
Sound Card on Board (SB Compatible+MPU401+AC97 Codec)
DELL P790 Multisync Monitor.
-------------------------------------------------------------------------------------------
Reused current installation from PII-333
-------------------------------------------------------------------------------------------
-------------------------------------------------------------------------------------------
Network Physical Configuration: (netword card slot are switched compared to PII-333 config)
------------------------------
+------+
|+----+|
|| ||
|+----+|
| |
|+---+ | manuf:
||== | | --> Network card: RTL8139 - REALTEK --> IP=dhcpclient eth0 (IRQ?)
|| | |
||== | | --> Network card: RTL8139 - UNEX --> IP=192.168.69.69 eth1 (IRQ?)
|| | |
|+---+ |
+------+
(private subnet) 192.168.*.*
--> Network: 192.168.69.*
--> Subnet mask: 255.255.255.0
--> Default gateway: 192.168.69.69
-------------------------------------------------------------------------------------------
Motherboard Soltek:
------------------
- Had problem with adcansys SCSI card when some of the features on the motherboard are disabled.
But when these features are enabled, it's Win98 which has problem with the SCSI card.
Below the settings for Win98/LInux for making the SCSI card works:
WIN98 LINUX
On Chip USB2 disabled enabled
On Chip Sound disabled enabled
On Chip IDE Channel 1 disabled enabled
Onboard Legacy Audio disabled enabled
Assign IRQ For VGA disabled enabled
Assign IRQ For USB disbaled enabled
-------------------------------------------------------------------------------------------
XFree86 Configuration (Monitor DELL P790 / RIVA TNT2):
---------------------
- Sub-part of file /etc/X11/XF86Config:
#The Following Monitor configuration was made by hand (Michael Peeters)
Section "Monitor"
HorizSync 31-92
Identifier "Monitor[0]"
ModelName "P790"
VendorName "DELL"
VertRefresh 50-150
# UseModes "Modes[0]"
Modeline "1024x768x85Hz" 94.50 1024 1072 1216 1376 768 768 784 809 +HSync +VSync
Modeline "1152x864x85Hz" 119.90 1152 1224 1360 1556 864 864 870 907 -HSync +VSync
Modeline "1280x1024x85Hz" 156 1280 1336 1552 1720 1024 1024 1039 1067 +HSync +VSync
Modeline "1600x1200" 162.00 1600 1664 1856 2160 1200 1201 1204 1250 +hsync +vsync
EndSection
Section "Screen"
DefaultDepth 16
SubSection "Display"
Depth 16
virtual 1152 864
Modes "1152x864x85Hz" "1280x1024x85Hz" "1600x1200" "1024x768x85Hz"
EndSubSection
Device "Device[0]"
Identifier "Screen[0]"
Monitor "Monitor[0]"
EndSection
- The following rules apply (obtain from DELL P790 specs, reverse engineer, error message
from file /var/log/XFree86.0.log and man pages)
- vsync & hsync polarity vary between resolution. +/+ appears to be mostly used for high pixel freq.
(sometimes wrong polarity can lead to strange screen!!!)
- Modeline "LABEL" pixfreq hres hsyncstart hsyncend hmax vres vsyncstart vsyncend vmax
values are computed as follows:
- INPUT: HRES, VRES, VFREQ (=60,75,85,100 Hz)
--> vmax = vres * 1.05 (~link to monitor structure)
--> hmax = hres * 1.35 (~link to monitor structure)
--> hfreq = vmax * VFREQ
--> pixfreq = hfreq * hmax
Here are rule of the thumb for other parameters:
--> hsyncstart = hres + 16
--> hsyncend = (hres+hmax)/2
--> vsyncstart = vres
--> vsyncend = vres + (5..10) (low offset for small res, high offset for hires)
- CAUTION, the following shall apply (also depends on the card drivers)
--> hfreq, vfreq and pixfreq must be in limit supported by the monitor and the card
--> hmax must be mult of 4
--> H blank width (ie. max(hmax,hsyncend) - min (hres,hsyncstart) ) must be mult of 4
--> H sync width (ie. hsyncend-hsyncstart) must be < 256
- to shrink/stretch horizontally: must increase/decrease hmax (hence increasing/decrease #pixel
per lines)
- to move horizontally: increase/decrease hsyncstart (or maybe hsyncend depending on polarity)
--------------------------------------------------------------------------------------------
Network Services:
----------------
- konqueror network browsing (example)
- List cerber network services (with Lisa) lan:cerber
- List cerber network services (with resLisa) rlan:cerber
- Connect to cerber FTP ftp://cerber/
- view cerber file file://cerber/
- connect to phoenix Samba smb://phoenix/
- Set LAN Browsing (only resLISA) (in konqueror, use 'rlan:cerber' eg. to connect to cerber services)
- Activate FTP
- uncomment line in /etc/inetd.conf
ftp ... ... in.ftpd
- send HUP to inetd
- Install QMail (see configuration txt file)
-------------------------------------------------------------------------------------------
============================================================================================
APPLICATION INSTALLED:
---------------------
- Opera 6.0 (RPMS Package) (install with kpackage)
- GetBinNews
- Wine
============================================================================================
UPDATE - PATCHES:
----------------
aborted
============================================================================================
POST-INSTALLATION CHANGES
============================================================================================
Configuration:
-------------
- setuid root /var/bin/smbmnt (to allow mounting smbfs by normal user)
- setuid root /var/bin/smbumount (to let unmounting them...)
- add local script for mounting phoenix W2k (/usr/local/bin/mntphoenix) (root/root/chmod 755)
& unmounting (/usr/local/bin/umntphoenix) (root/root/chmod 755)
! PROBLEM: SLOW PERFORMANCE !!! (50kB/s !!!)
- Installed package kernel k_deflt-2.4.16-22.i386.rpm
Installed package modutils-2.4.12-11.i386.rpm
Installed package resierfs-3.x.0k_pre10-8.i386.rpm
--> SOLVE PERFORMANCE ISSUE FOR SMBMOUNT (now 4MB/s !!!)
(source: http://www-1.ibm.com/servers/eserver/iseries/netserver/smbfs_faq.htm)
Problem: smbfs performance is poor for larger file transfers.
Solution:
Currently, Samba has a "bug" in the way it determines the appropriate blocksize to use
for file transfers. Only 512 bytes are transferred per read/write request, instead of
the normal 4K transfers. There is a partial fix for this problem in the 2.4.11 kernel.
Users who experience slow transfers should upgrade to at least this kernel level.
The smbclient utility is not affected by this problem.
--------------------------------------------------------------------------------------------
- Modified /etc/X11/XF86Config to allow wheel mouse support
- created symlink /dev/cdrecorder --> scd1 (for cdrdao)
ln -s /dev/scd1 /dev/cdrecorder
- Updated samba server configuration (added line: encrypt passwords=yes; added password with smbpasswd)
--------------------------------------------------------------------------------------------
- Downloaded & Installed ntop 2.0.0
- Downloaded & installed libpcap-0.7.1
- installed gdchart0.94c (came with ntop tar.gz)
- gd-1.8.3 was already installed
- installed zlib-1.1.3
- Create suse package ('make make-suse')
--> small error during makefile, missing target parent directory for intop.1 manpage
(WORKAROUND: create the missing directory, re-run makefile)
- Launch ntop at boot (set yes in rc.config)
--------------------------------------------------------------------------------------------
- Make cdrecord available to all users:
cdrecord can be safely setuid to root:
su
(cd to directory where cdrecord is installed)
chown root cdrecord
chmod 4711 cdrecord
--------------------------------------------------------------------------------------------
SHELL STARTUP CONFIGURATION:
---------------------------
- added .cshrc (see file in config/cshrc)
in /root/
in ~baddreams/
in /etc/skel/
purpose: change history key bindings, clean up redundant entries in path
- added path.csh in /etc/profile.d/ (see file in config/path.csh)
purpose: complete path definition for all users with shells tcsh/csh
- added /etc/skel/.bashrc in /root/
added /etc/skel/.profile in /root/
--------------------------------------------------------------------------------------------
X CONFIGURATION:
---------------
- Deactivated klipper URLGrabber:
in file .kde2/share/config/klipperrc:
...
URLGrabberEnabled=false
--------------------------------------------------------------------------------------------
SCRIPTS ADDED IN /usr/local/bin:
-------------------------------
- noerr (to discard stderr output)
- iplog (to log & reject internet connections)
- mntphoenix & umntphoenix (to mount phoenix samba shares)
--------------------------------------------------------------------------------------------
Added new IDE CDROM in IDE-0, SLAVE:
-----------------------------------
New symlink:
- ln -s /dev/hdb /dev/cdrom2
--------------------------------------------------------------------------------------------
- Activated autofs
----------------
as root:
--> in /etc/rc.config, START_AUTOFS="yes"
--> edited /etc/auto.master (auto mount point is /auto)
# $Id: auto.master,v 1.1 2001/04/17 11:43:02 arvin Exp arvin $
# Sample auto.master file
# Format of this file:
# mountpoint map options
# Also see variable AUTOFS_OPTIONS in /etc/rc.config
# For details of the format look at autofs(8).
/auto /etc/auto.misc --timeout 60
--> edited /etc/auto.misc
# $Id: auto.misc,v 1.1 2001/04/17 11:43:02 arvin Exp arvin $
# This is an automounter map and it has the following format
# key [ -mount-options-separated-by-comma ] location
# Details may be found in the autofs(5) manpage
#kernel -ro ftp.kernel.org:/pub/linux
#removable -fstype=ext2 :/dev/hdd
#cd -fstype=iso9660,ro :/dev/hdc
floppy -fstype=auto :/dev/fd0
cd -fstype=auto,ro :/dev/cdrom
cd2 -fstype=auto,ro :/dev/cdrom2
cdrec -fstype=auto,ro :/dev/cdrecorder
--> edited /etc/fstab to remove old mount point (now all manual mount points are in /mnt)
/dev/hda3 swap swap defaults 0 0
/dev/hda7 / ext2 defaults 1 1
/dev/hda6 /boot ext2 defaults 1 2
/dev/fd0 /mnt/floppy auto noauto,user 0 0
proc /proc proc defaults 0 0
/dev/cdrom /mnt/cd auto ro,user,noauto,unhide
/dev/cdrecorder /mnt/cdrec auto ro,user,noauto,unhide
# End of YaST-generated fstab lines
/dev/hda1 /mnt/hda1 vfat users 0 0
/dev/hda5 /mnt/hda5 vfat users 0 0
/dev/cdrom2 /mnt/cd2 auto ro,user,noauto,unhide
--> Created symlinks to auto mount points:
mkdir /auto
ln -s /auto/cd /cd
ln -s /auto/cd2 /cd2
ln -s /auto/cdrec /cdrec
ln -s /auto/floppy /floppy
--------------------------------------------------------------------------------------------
2003-03-12 Configuration of the ADSL Firewall Router USB/4 PORTS SWITCH (BIPAC-741):
-----------------------------------------------------------------------------------
Configuration of the Modem:
--------------------------
LAN Settings:
IP Address: default (ie. IP address=192.168.1.254, mask=255.255.255.0)
DHCP Server: DHCP enabled, start address=192.168.1.100, max. 100, DNS/WINS auto
WAN Settings:
ISP: Protocol: PPPoE, VPI:8, VCI:35
NAT enabled, Encapsulation Method: LLC/SNAP
User Name: *****
Password: *****
Service Name:
Specify an IP Address:
Authentication Protocol: AUTO
Connect on demand (auto-disconnect after 60 minutes)
DNS: Obtain a DNS address automatically
System Settings:
PASSWORD: ****
TIMEZONE: Brussels, apply daylight saving
LINUX Configuration:
-------------------
- LINUX PC will act as the mail server for the LAN (POP proxy), hence will receive a fixed IP address
- IP Address= 192.168.1.69 (ie. outside the DHCP range to avoid conflict)
- DNS = 192.168.1.254 (ie. the MODEM ITSELF!!! that will act as a DNS relay)
- ROUTE = default gateway is 192.168.1.254 (ie. the modem)
NOTE: MODEM DHCP Server is not compatible with DHCLIENT (some settings are accepted, but not all)
--------------------------------------------------------------------------------------------
2003-07-05 Changed Samba configuration to sync. with new IP address (ADSL router)
--------------------------------------------------------------------------------------------
--> change file /etc/samba.conf:
hosts allow = 192.168.1. 127. (instead of 192.168.69. 127.)
interfaces = 192.168.1.69/24 (instead of 192.168.69.69/24)
--------------------------------------------------------------------------------------------
2004-05-22 Enabled NFS Server
--------------------------------------------------------------------------------------------
- Enabled with YAST2. Config files changes are:
- /etc/rc.config:
NFS_SERVER="yes"
- /etc/exports
/c \
192.168.0.0/255.255.0.0(ro,all_squash)
/d \
192.168.0.0/255.255.0.0(ro,all_squash)
/home \
192.168.0.0/255.255.0.0(ro)