Lacie NAS rooting

From miki
Revision as of 20:15, 26 April 2017 by Mip (talk | contribs)
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to navigation Jump to search

Log

Content of file lacie-nas-rooting.txt:

ROOTING LACIE-CLOUDBOX

Following instructions from http://lacie.nas-central.org/wiki/Category:CloudBox
(Using clunc)
Another relevant thread: http://forum.nas-central.org/viewtopic.php?f=277&t=7215&start=15
Another wiki page, very long: http://lacie.nas-central.org/wiki/Category:2big_Network_2#Debian_.22Squeeze.22_.28stable.29_Chroot_Environment

- Get CLUNC

# CLUNC Home: http://lacie-nas.org/doku.php?id=clunc
git clone 'http://git.lacie-nas.org/clunc.git'

- Build CLUNC

cd clunc
make

- Create file telnetd.sh
 #!/bin/sh
 /usr/sbin/telnetd -l /bin/sh

##################################################################################
beq06659@nxl67170ux ~/work/_git/clunc (master)
$ ./clunc -i 172.19.100.98

Marvell>> setenv console "ttyS0,115200 a=a;/*/*/telnetd.sh"
setenv console "ttyS0,115200 a=a;/*/*/telnetd.sh"
Marvell>> ide reset
ide reset

Reset IDE: 
Marvell Serial ATA Adapter

Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (5)
  Device 0 @ 0 0:
Model: ST3000DM001-1CH166                       Firm: CC47     Ser#:             Z1F4SDRK
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 2861588.4 MB = 2794.5 GB (5860533168 x 512)
PCIe SATA:ffffffff

Marvell>> run nexus_boot
run nexus_boot
Booting Nexus layout from disk 0...
boot_count=0
saved_entry=1
Loading file "/boot/uImage" from ide device 0:5 (gpt5
)
7182500 bytes read

## Checking Image at 00800000 ...
   Image Name:   Linux-2.6.31.14-svn7493
   Created:      2014-10-17  14:00:55 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    7182436 Bytes =  6.8 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
## Error: "rescue" not defined
## Booting image at 00800000 ...
   Image Name:   Linux-2.6.31.14-svn7493
   Created:      2014-10-17  14:00:55 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    7182436 Bytes =  6.8 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK
bootargs from environment variables : ttyS0,115200 a=a;/*/*/telnetd.sh boot=UUID=cd7a1c60-168d-4679-9217-bb43aeacecf8 root=UUID=998d1e20-6baf-4595-a736-8f5ce2b993b7 cap=gpt,lba64

Starting kernel ...
##################################################################################

- After 2min, telnet to cloudbox:

telnet lacie-cloudbox

/etc/unicorn/unicorn_conf # uname -a
Linux LaCie-CloudBox 2.6.31.14-svn7493 #1 Fri Oct 17 14:00:51 UTC 2014 armv5tel GNU/Linux

 cd /etc/initng/runlevel
 cp default.runlevel default.runlevel.bak
 sed -i '/^#sshd$/s/^#//' default.runlevel

1. Remove comment from sshd in the default.runlevel file, so initng will start it at boot time: 
 cd /etc/initng/runlevel
 cp default.runlevel default.runlevel.bak
 sed -i '/^#sshd$/s/^#//' default.runlevel

2. Enable sshd in Unicorn 
 cd /etc/unicorn/unicorn_conf
 cp unicorn.sharing.ssh.conf unicorn.sharing.ssh.conf.bak
 sed -i '/enabled:.*false/s/:.*/: true/' unicorn.sharing.ssh.conf

2. Enable root login for sshd (necessary on first manual start apparently)
cd /etc/ssh
cp sshd_config sshd_config.bak
sed -i '/PermitRootLogin.*no/s/no/yes/; /AllowUsers/s/$/ root/' sshd_config

3. Start sshd 
 ngc --start sshd

You should now be able to connect on port 2222.

4. On client. Setup .ssh/config:

Host lacie
    User                root
    HostName            lacie-cloudbox.local
    ProxyCommand        none
    ForwardX11          no
    ForwardX11Trusted   no
    Port                2222

5. Connect

    ssh lacie

    [root@LaCie-CloudBox ssh]#

Voilà!


#################################
TODO:
- Exclude .gvfs from backup
- Backup must include truecrypt volume. Check if we need --checksum option
- Backup vbox on c partition on nxl67170ux
#################################
$ wakeonlan 00:d0:4b:96:34:32
Sending magic packet to 255.255.255.255:9 with 00:d0:4b:96:34:32
#################################
Basic performance tests:

(on griffin)
$ dd if=/dev/zero of=/data/tmp/ddfile bs=1024k count=20000
20971520000 bytes (21 GB) copied, 270,671 s, 77,5 MB/s

(from nxl67170ux to lacie under desk) 
$ dd if=/dev/zero of=/smb/lacie-cloudbox/family/ddfile bs=1024k count=20000
858783744 bytes (859 MB) copied, 19,2096 s, 44,7 MB/s
...
4579131392 bytes (4,6 GB) copied, 123,565 s, 37,1 MB/s

(from nxl67170ux to mnemosyne under desk) 
$ dd if=/dev/zero of=/smb/lacie-cloudbox/family/ddfile bs=1024k count=20000
246415360 bytes (246 MB) copied, 3,13408 s, 78,6 MB/s
...
5197791232 bytes (5,2 GB) copied, 143,574 s, 36,2 MB/s
#################################
Q: HOW COME I CAN NAME RESOLV ON LACIE-CLOUDBOX WITHOUT HOSTS FILE?
--> uses nmblookup. But it gives bad address if remote pc has both eth0 + wlan0


#################################
CGI on Mnemosyne

cfr http://synology.asfi-fr.com/tutos_phi/%5Btuto%5D%20syno%20CGI.pdf

######################################################################################
######################################################################################
######################################################################################
######################################################################################
######################################################################################
######################################################################################
######################################################################################

TODO:
- Force lacie-cloudbox to use wired ip address when available (not the wlan)
- Don't exclude completely /var/log, but only some of them (eg. rsync.log)
- Disable rsyncd transfer logging on client
- Configure email notification

NTP CONFIGURATION:
Frequent time desync.
Change server to 0.ubuntu.pool.ntp.org